How to make easy concrete pumpkins

Concrete pumpkins have been on my “To DIY” list for a couple years, but I kept putting the project off because Practical Lisa couldn’t justify buying a big ole 50-pound bag of concrete mix just so Creative Lisa could make a couple of decorative pumpkins.

diy concrete pumpkins in a fall vignette

Over the summer, I stumbled upon a solution to my conundrum: Henry FeatherFinish Underlayment Patch and Skimcoat.

Henry FeatherFinish Skimcoat for cement pumpkin craft project

Technically the product — which is sold in small 7-pound boxes — is designed for patching and repairing subfloors. But a few DIY’ers who I follow online had applied it to their laminate countertops to make them look like solid concrete.

I figured if it worked for countertops, it would work for pumpkins, too, right? I was willing to at least test my theory and find out.

Materials and supplies

Here’s a list of supplies and materials I used to make my easy concrete pumpkins:

  • Styrofoam pumpkins
  • Henry FeatherFinish Skimcoat*
  • Two small plastic buckets (one to mix the skimcoat in; another for water)
  • Paint stick
  • Paper towels (for cleanup)
  • 120-grit sandpaper
  • Thick wire (if your pumpkins don’t have stems)
  • Jute twine
  • Clear craft glue
  • Markers (to wrap twine around)

*I got my box of skimcoat at Home Depot. (Word to the wise: If you’re looking for it in the store, it’s in the flooring aisle, not the cement aisle.)

Making easy concrete pumpkins

Thrift Store Styrofoam Pumpkins Before Makeover

Here are the three pumpkins I started with for this project. All three were thrift store finds. I really didn’t care what they looked like as long as they had an overall pumpkin-y shape.

Small Styrofoam Pumpkins Before Makeover

Before I could start skimcoating, I had to rip off the extraneous leaves and whatnot, and part of the pumpkins’ plastic covering came off too. No worries. I figured I could smooth over the mess I had created with the skimcoat.

Wire cutters snipping a piece of wire off a coil

Next, I grabbed some heavy wire from my husband’s workshop and cut off a couple of small pieces to serve as stems for the pumpkins that didn’t have them.

Pumpkins with wire handles before applying cement skimcoat

I popped the new stems in place. Then I was ready to mix the skimcoat.

Mixing the skimcoat

Cement skimcoat in bucket before water is added

I did this part of the project outside because it’s kind of messy.

The directions say to mix two parts powder to one part water, so I put a cup of powder in a plastic bucket and added half a cup of water. Turns out, this made about twice as much skimcoat as I needed for three pumpkins.

Mixing cement skimcoat for pumpkin craft project

I mixed the ingredients with an old paint stirring stick. The skimcoat was about the consistency of frosting.

It spread a lot like frosting, too. I didn’t use a knife though.

Wet cement on DIY concrete pumpkin craft

I scooped the skimcoat up in my hands and spread it on with my fingers. Yes, it’s messy. But I had to be able to mold the skimcoat to the curves of the pumpkin, and fingers seemed like the best tool for the job.

Bucket of Water for Smoothing Cement Skimcoat

You might want to wear rubber gloves if you try this. Otherwise plan to rinse your hands in a bucket of water or spray them off with your garden hose when you’re done. (You don’t want to wash the residue down your your kitchen drain. It will harden in your pipes if you do.)

I still had a bunch of skimcoat left over once I had my three pumpkins coated, so, after cleaning up my hands, I dashed back into my house and dug through my stash of fall decorations in search of additional Styrofoam pumpkins.

Luckily, I had two more tucked away in my basement, and I made it back outside before the leftover skimcoat had hardened in the bucket.

Smoothing the skimcoat

Smoothing out cement skimcoat on decorative pumpkin

Once I got skimcoat on the two late additions, I dipped my fingers in water and started smoothing out the lumps and bumps on the surfaces of all five pumpkins.

Styrofoam Pumpkin With Cement Skimcoat

The smoother the skimcoat is when it’s wet, the less sanding you’ll have to do when it’s dry.

Obviously, I couldn’t coat an entire pumpkin at one time because I needed to be able to set it down on my work table while I was applying the goo. I just covered as much area as I could, working from the top down.

Cement pumpkins prior to sanding

Here are what my pumpkins looked like as they started to dry. The lighter grey areas are dry; the darker areas are still wet.

I took a break at this point and let the pumpkins dry for a couple hours. I probably wouldn’t have had to wait that long — the box said the product dries in as little as 15 minutes — but I had other things to do.

Bottom of pumpkins, after concrete had dried on the top halves

When I came back outside, I flipped the pumpkins over, mixed up a much smaller batch of skimcoat and coated the bottoms, following the same process as before.

Smoothing out the cement on the bottom half of a pumpkin

I tried to blend the wet skimcoat with the dried portion as seamlessly as possible, so there wasn’t a noticeable line between the two halves.

Sanding a concrete pumpkin

When the bottoms dried, I sanded off all the ridges and highpoints, using 120 grit sandpaper.

Pumpkins after concrete has dried

Here’s how my pumpkins looked once I was done sanding.

Creating stems and vines

With the concrete work done, I moved on to the stems and vines. I used jute twine and some clear gel glue that I had in my crafts stash for this.

Winding jute twine around wire to form a stem on concrete pumpkin

To cover the wire stems, I adhered the end of the twine to the bottom of the stem. Then I wound the twine up the stem and back down again.

Winding jute twine around wire stem on concrete pumpkin

When I had the stem all covered, I dabbed a bit of glue onto the other end of the twine and tucked it under.

Winding twine around markers to create twirling vines for concrete pumpkins

To make vines, I dipped the end of a marker into glue and then wrapped twine around the marker.

Removing twine vine from end of marker

I let the glue set up for a few minutes — long enough for the coils to be a bit stiff, but short enough that they would still slide off the markers.

Then I pulled the coils apart to loosen them up and give them a more natural shape.

Small concrete pumpkin with jute stem and vines

Finally, I looped the vines around the pumpkin stems and moved them around until I was happy with how they looked.

DIY concrete pumpkins made with skimcoat

Honestly, you’d never know these pumpkins were not solid concrete, until you tried to lift one. They are light as a feather, which should make it easy to carry them around and store them in the off-season.

I’m very happy with how they turned out. In fact, I’m tempted to go and skimcoat all of my faux pumpkins now.

Easy DIY Concrete Pumpkins by Wisconsin Magpie

What do you think? Leave a comment. I love to hear from readers. And if you like this post, please share it on social media and pin my photos on Pinterest. Thanks!

Lisa

8 Replies to “How to make easy concrete pumpkins”

Leave a Reply